Stainless steel

We offer hot-rolled, forged and cold-drawn rods for the following purposes:

1. Structural
2. For improvement
3. In an improved state
4. For cementation
5. Steels for automatic machines
6. Tool steels
7. Wires

The general division of steel is shown in the following table:

1.jpg - Šipkasti čelici

1. Structural (carbon) steels

Structural (carbon) steels are used for the construction of various structures (cranes, carriers), in construction (bridges), in the machinery industry (vehicle parts, ship structures, machinery parts), oil industry and the like. These steels are applied in the raw state (without thermal treatment).

Round steel

OKRUGLI[1].jpg - Šipkasti čelici
OKRUGLI-2[1].jpg - Šipkasti čelici

Square steel

KVADRATNI[1].jpg - Šipkasti čelici
KVADRATNI-2[1].jpg - Šipkasti čelici

Float steel

plocni[1].jpg - Šipkasti čelici


2. Improvement steel

The improvement steel can be carbon (unalloyed) and low-alloyed, which by the heat treatment process (hardening and releasing) achieves the appropriate toughness properties, but also the required toughness. These steels are most commonly used in the machinery industry (shaft and shaft production), auto industry, dedicated industry, shipbuilding, metal processing (making screws, wedges, lugs, etc.).

poboljsanje[1].jpg - Šipkasti čelici
poboljsanje-2[1].jpg - Šipkasti čelici
The main characteristic of the improved steels is that they are hardened in water with forming temperatures and further reduced at a temperature of 680-710 ° C, achieving the appropriate toughness properties, but also the required toughness. They have the same, or similar application as the steels for improvement.


3. Cement steel

The cement steel represents a group of steel, which, after processing, separates the particles from the outer surface. After hardening the outer layer, tempering is carried out in order to achieve high resistance of the outer layer to wear, and increased toughness of the non-core. The pre-fat cementation cells generally contain 0.1-0.2% C, and after annealing, the outer layer contains 0.8-0.9% C. The process of grooming is called cementation. These steels are used in the machinery industry (making gears of other gears), the dedicated industry (manufacture of weapons), shipbuilding, metalworking, etc.



4. Steels for automatic machines

The automatic steels are intended for the production of parts on high-performance automatic machines. Their basic characteristic is better workability compared to other steels. The ability to process these steels is achieved by means of an altered chemical composition which facilitates the formation of inclusions, which enable the formation of brittle and short shavings.


5. Tool steels

Alatni čelici su plemeniti ugljenični ili legirani čelici sa udjelom ugljika od 0,6 % do 2,06 % ili legirani (uglavnom sa Cr, W, V, Mo, Co), a koristi se za izradu alata. Osnovna svojstva koja alatni čelici moraju posjedovati su otpornost na trošenje i visoka udarna izdržljivost. Proizvodni (ekonomski) zahtjevi i svojstva prema alatnim čelicima su: mogućnost obrade alata odvajanjem čestica, visoka zakaljivost, visoka prokaljivost, neznatna promjena dimenzija tokom rada, mogućnost obrade, otpornost na koroziju, mogućnost poliranja, ekonomičnost itd.


6.  We offer wires of the following type and dimensional assortment

  • Light string for nails, dimensions 1.40 - 10.0 mm
  • Annealed wire, dimensions 1.40 - 3.4 mm
  • Galvanized wire, dimensions 1.80-4.50 mm
  • Plugs for galvanic protection, dimensions 2.0-10.0 mm